
If your Air Dancer fabric has torn, faded or needs new artwork, you may be able to reuse its blower. Before ordering a replacement air dancer tube, give the supplier enough information to confirm that the new tube will attach to your blower and operate in the configuration you intend to buy. Start with the equipment you have on site. The height of the old tube is one useful detail, but the blower model and attachment tell the supplier what it needs to match.
Photograph the complete blower and take a close-up of the nameplate. Copy the manufacturer, model number and any revision or serial number shown. If the rating label lists voltage, frequency, power or speed settings, send a readable photo so the supplier can distinguish versions that look alike. Include the model or part reference from the old fabric tube if it is still legible.
If the blower label is missing, send the original order record or manual if you have it. Include top and side photos of the housing and outlet. Let the supplier know which details remain unknown so it can tell you what evidence it needs to identify the blower. If the fan itself also needs replacing, see the commercial inflatable blower guide.
With the blower switched off and disconnected, remove the fabric tube according to the equipment instructions. Photograph the outlet from above and from the side. For a round fitting, record the outside diameter at the point where the fabric attaches. If a raised lip or ring sits above that point, label its diameter separately. Show the ruler or tape in the photo and indicate where each measurement was taken. For a fitting of another shape, give the supplier the relevant dimensions and a clear outline photo.
Lay the old fabric opening flat without stretching it and photograph it beside the ruler. Label that reading as the flat opening width. Ask the supplier which measurement its catalogue uses and where it is taken. A supplier may ask for another measurement or a drawing before it confirms fit. Use the spare-parts compatibility guide to retain the approved part reference for later orders.
Take a close-up of both sides of the attachment. For hook-and-loop fastening, show which surface is on the blower and which is on the tube, along with the position and width of the strip. If your model uses a clamp or another fitting, show the hardware and the point it grips. Photograph any adaptor you intend to reuse and include its part number if available.
Ask the supplier to state the attachment it will supply and identify any additional parts needed. Then request confirmation that the existing blower is suitable for the proposed tube height and shape, including the number of outlets or blowers the design requires. A taller tube or a change from a single-leg to a two-leg design calls for a fresh compatibility check. The Air Dancer buying guide covers complete systems if you want to compare a new kit.
Subject line for your email: Replacement Air Dancer tube only for blower [make and model]. Attach the labelled photos and ask the supplier to fill in the last column.
| Field | Buyer to complete | Supplier to confirm in writing |
|---|---|---|
| Existing blower | Make/model: ___; revision or serial: ___; nameplate photo: ___ | Exact blower model or configuration checked |
| Outlet dimensions | Shape: ___; outside diameter or dimensions at attachment: ___; units and photo: ___ | Required outlet dimension and where it is measured |
| Old tube opening | Old part ID: ___; flat opening width and units: ___; photo: ___ | Replacement tube part ID and corresponding opening dimension |
| Fastening and hardware | Fastening type: ___; photos of both sides: ___; adaptor or clamp ID: ___ | Mating fastening and any parts required, with inclusions listed |
| Proposed tube | Desired height: ___; shape and number of legs: ___; artwork: ___ | Supported configuration for the existing blower, with any restrictions |
| Order and delivery | Quantity: ___; destination and postcode: ___; required arrival date: ___ | Tube-only scope, drawing or revision, dispatch estimate and shipping terms |
If the old tube has no label, mark its reference as unknown and attach the nameplate, outlet, closure and old opening photos. Suppose the supplier says the outlet size matches but cannot confirm the mating fastening. Ask for the attachment drawing or a photo of the offered part, and compare it with yours before placing the order. If fit is confirmed only for a particular adaptor or tube height, include that condition on the order. For repeat purchases, keep the approved drawing or part number and supplier confirmation with the request for quotation and purchase record.